Reducing Demolding Forces in Injection Molding

Sticking components, high ejector forces, and unstable demolding processes – particularly those caused by mold deposit formation – are among the most common challenges in injection molding. High demolding forces or deposits occur particularly with high-gloss surfaces, microstructures, engineering thermoplastics, or narrow process windows, leading to scrap, mold modifications, and unplanned downtime.

Plasma-based UltraPLAS® PECVD release coatings selectively influence adhesion and friction, sustainably reducing demolding problems – without transfer to the component or changes to the mold geometry. They can also broaden the injection-molding process window.

Causes of High Demolding Forces

Demolding force results from the interaction of several effects, particularly:

  • Adhesion between the hot polymer and the mold surface
  • Friction along the molded-part surface
  • Mechanical interlocking (e.g., due to microstructures or geometry)
© Fraunhofer IFAM

Temperature control is a key influencing factor in the process:

  • High mold temperatures → adhesion dominates (e.g., local hot spots)
  • Low temperatures → greater shrinkage and lower adhesion, but increased contact pressure → consequently higher friction

In many industrial applications, adhesion is the dominant factor and therefore the principal lever for sustainably reducing demolding forces.

 

Mold deposit formation as an additional influencing factor:

An additional and frequently underestimated factor is mold deposit formation (mold fouling or plate-out): even ultrathin films that are often visually undetectable can alter the surface properties and significantly increase the tendency to stick.

Critical Applications for Demolding Problems

Elevated demolding forces occur particularly frequently with:

  • Elastomers and soft thermoplastics
  • High-performance polymers (e.g., PEEK, PPS, PA with additives)
  • High-gloss polished and microstructured cavities
  • Processes with narrow thermal windows
  • Small draft angles
  • Suboptimal mold temperature control
  • Materials prone to mold deposit formation (e.g., recyclates and flame-retardant grades)

In such cases, conventional process- or mold-related measures frequently reach their limits.

Operating Principle of Mold Coatings

Mold coatings selectively modify the interface between the polymer and the mold. Two parameters are decisive:

  1. Surface chemistry: influences adhesion, wetting behavior, sticking tendency, and release characteristics
  2. Topography and roughness: determine the coefficient of friction, actual contact area, tribological behavior, and demolding dynamics

Targeted adjustment of these properties stabilizes demolding conditions and improves them reproducibly. For this purpose, Fraunhofer IFAM has developed plasma-based PECVD release coatings marketed under the UltraPLAS® brand.

UltraPLAS® – Plasma-Based PECVD Release Coatings

The UltraPLAS® coatings developed at Fraunhofer IFAM are deposited by PECVD and specifically designed for demanding injection-molding processes. Their key characteristics include:

  • Conformal coating (thicknesses below 200 nm possible) without dimensional changes
  • Preservation of polish, microstructure, and optical appearance
  • Very low surface energies
  • High mechanical and chemical stability
  • Transfer-free release behavior without contamination of the component or consumption of the coating ⟶ optimal for medical, food contact, etc.
TPE-S without a release coating
© Fraunhofer IFAM
TPE-S without a release coating: The parts stick together and can only be removed from the mold by warping them
TPE-S with UltraPLAS® coating
© Fraunhofer IFAM
TPE-S with UltraPLAS® coating: Parts fall right out of the mold; no warping during demolding

Technical Effects in the Injection-Molding Process

A targeted modification of the interface can:

  • Significantly reduce demolding and ejector forces
  • Enable higher demolding temperatures
  • Stabilize adhesion-driven problems
  • Ensure reliable demolding of microstructured and high-gloss surfaces
  • Create tribologically optimized surfaces

Comparison with Conventional Release Systems

Conventional release aids are often based on silicone coatings, PTFE topcoats, or solid lubricants. These systems perform reliably in many applications but reach their limits with demanding surfaces and high mechanical loads.

Typical limitations include:

  • Low wear resistance
  • Consumption or abrasion of the release layer
  • Sensitivity to cleaning
  • Transfer of release-active constituents to components
  • Limited suitability for high-gloss surfaces
  • Potential concerns regarding regulatory requirements

 

By contrast, UltraPLAS® PECVD release coatings are:

  • Firmly bonded to the substrate
  • Durably stable
  • PFAS-free
  • Transfer-free
  • Suitable for demanding applications (e.g., medical technology, high-gloss optics, and microstructures)

Economic Benefits and Process Advantages

Depending on the application and boundary conditions, the use of UltraPLAS® coatings can provide the following improvements:

  • Lower demolding forces and reduced ejector wear
  • Less mold deposit buildup due to self-cleaning effects
  • More stable process windows
  • Reduced warpage and component damage
  • Simplified mold design (e.g., fewer slides)
  • Shorter cycle times through higher demolding temperatures

Systematic Approach: Understanding Causes Instead of Trial and Error

Not every demolding problem has the same cause. The process therefore always begins with an analysis of the material, component geometry, mold surface, and process control.

On this basis, we assess which factors dominate demolding and whether a coating can make a relevant contribution to process stabilization. We then design suitable coating systems, validate them using sample components, and support implementation under real production conditions.

Target Groups and Fields of Application

Our services are particularly relevant to:

  • Injection-molding companies
  • Tool and mold manufacturers
  • Plastic processing companies
  • OEMs of technical plastic components
  • Applications involving high-gloss or textured surfaces

Would You Like to Resolve Demolding Problems in a Targeted Manner?

Whether the issue involves sticking components, high ejector forces, or mold deposit formation, stable demolding requires a clear understanding of the underlying mechanisms.

We would be pleased to support the assessment of your application and jointly determine whether our release coatings can improve demolding behavior, process stability, and cost-effectiveness.